Part Library

Ready-made 3D-printable parts in fixed sizes: handles, hooks, brackets, cable clips, organisers and more. Pick a size and get an instant quote.

Bike

• Accessory bar shim - Split sleeve that fills the gap when an accessory clamp, such as a bell, light or mirror, is bigger than the bar. For accessory clamps only. Not for stem, brake lever or shifter clamps. Check fit and clearance on your own bike before riding.
• Accessory lever shim - Spacer shim for accessory levers only, such as a dropper-post lever or shifter reach adjuster. Never for brake levers. Measure your own pivot before choosing. Check fit and clearance on your own bike before riding.
• Handlebar end plug - Plug for the open end of a handlebar tube, with a finger notch in the head. Measure your own tube bore first. Check fit and clearance on your own bike before riding.
• Bar tape end plug - End plug for road-bar tape with a round head that sits over the tape edge. A finishing piece. Check fit and clearance on your own bike before riding.
• Outboard guard plate - Thin ribbed outboard disc for a single-speed or gearbox setup, on three fixed bolt holes with bought M5 bolts and spacers. Check chain offset, tyre and frame clearance first. It is not an axle, dropout or drivetrain part. Check fit and clearance on your own bike before riding.
• Frame-boss cable clip - Clip that sits under the head of a frame-boss bolt and snaps over one or two gear housings. Check fit and clearance on your own bike before riding.
• Bottle cage angle adapter - Wedge adapter on 64 mm bosses that tilts the bottle cage. Check bottle and tyre clearance. Check fit and clearance on your own bike before riding.
• Bottle cage offset adapter - Plate for frames with 64 mm boss spacing, with a second pair of holes shifted along the plate to set the offset. Check bottle and tyre clearance. Check fit and clearance on your own bike before riding.
• Frame cable guide (tie-on) - Saddle that sits on a frame tube and holds gear housing or a hose in line, with tie slots either side of the groove. For tubes away from the wheel. Check fit and clearance on your own bike before riding.
• Cassette rack - Bench rack that stores a cassette on a post with a flange for the large cogs to rest on. Not spline-keyed.
• Chain checker body - Body of a go/no-go chain checker: a bar with two press-fit pin holes set a fixed offset beyond six inches. Pins are bought 3.5 mm pins, not included. Positions are nominal; it gives no wear verdict.
• Chain-slap shell - Curved shell for the underside of the chainstay, bolted through two fixed holes to existing frame bosses with your own M5 bolts. After fitting, turn the cranks through a full pedal turn in every gear and check chain movement and mud clearance by hand. Check fit and clearance on your own bike before riding.
• Chainline ruler - Flat ruler with a lip that lays against the seat tube and a scale measured from the tube centre, for a visual check of chainline. A visual aid; accuracy is not stated.
• Chainstay guard, oval tube (TPU) - Half-shell in TPU 95A for an oval or flattened chainstay, held on by zip ties. Measure both axes of your tube. Generic profile, not matched to any brand. Check fit and clearance on your own bike before riding.
• Chainstay guard, round tube (TPU) - Short half-pipe shell in TPU 95A for a round chainstay, held on by zip ties. Generic profile, not matched to any brand. Check fit and clearance on your own bike before riding.
• Chainstay wrap (split, TPU) - Flexible split wrap in TPU 95A that goes on from the side, with strap slots for a hook-and-loop strap or zip tie. Measure your own stay where it will sit. Check fit and clearance on your own bike before riding.
• Out-front computer mount - Bar clamp with a forward arm and a quarter-turn dock modelled to commonly published dimensions. Test-fit your own computer before riding. Never replaces a stem cap. Check fit and clearance on your own bike before riding.
• Disc pad gap gauge - Workshop measuring aid only, nothing fitted to the bike: a stepped block for a by-eye look at the rotor-to-pad gap. Print tolerance is about 0.2 mm, so treat it as a guide and check against a proper tool.
• Generic display mount - Bar clamp with a plate and tie slots for a small display. No brand-specific hole pattern: match your display with ties or your own drilling. Has a tether hole. Check fit and clearance on your own bike before riding.
• Dropout spacing gauge - Workshop measuring aid only, nothing fitted to the bike: a flat reference bar for a go/no-go look at rear dropout spacing. Print tolerance is about 0.2 mm and parts can warp, so it is a visual aid; check against a proper tool.
• Fender bridge bracket - Bracket for a fender at a seat-stay or chainstay bridge boss, with a slot for the fender's own fixing. Check tyre clearance with the tyre loaded and allow for mud. Check fit and clearance on your own bike before riding.
• Fender fork bracket - L-shaped bracket for a fender, mounted at a fork or frame M5 boss. Check tyre clearance with the tyre loaded and allow for mud. Check fit and clearance on your own bike before riding.
• Fender stay - I-beam stay with an adjusting slot at each end so one stay suits several wheel sizes. Spin the wheel with the stay fitted and look for contact with spokes and tyre before riding. Check fit and clearance on your own bike before riding.
• Frame port bung (TPU) - Flexible flanged bung in TPU 95A for a drilled frame port with a cable or hose already routed. A side slot clips it over the cable. Not a seal. Check fit and clearance on your own bike before riding.
• Frame port grommet - Split flanged bush that lines a drilled frame port so housing does not rub the edge. Fits over housing already in place. Not a seal. Check fit and clearance on your own bike before riding.
• Hanger alignment pointer - Workshop measuring aid only, nothing fitted to the bike: a pointer arm held against the rim while you read a bought hanger gauge or ruler. Print tolerance is about 0.2 mm, so check against a proper tool.
• Handlebar light mount - Bar clamp for a light with a recess for a TPU liner strip, a tether hole for a lanyard and an arc slot for angle. Fit your own light and tether, and check it cannot reach the wheel or brake. Check fit and clearance on your own bike before riding.
• Fork light mount - Strap-on saddle for a light on a fork leg, with a recess for a TPU liner strip, a tether hole for a lanyard and an arc slot for angle. Check the light and tether clear the wheel, brake and mudguard. Check fit and clearance on your own bike before riding.
• Helmet light mount - Curved base for a light on top of a helmet, with strap slots, a recess for a TPU pad, a tether hole and a tilt slot. Check the helmet vents, strap path and a clear head turn. Check fit and clearance on your own bike before riding.
• Phone mount for bars - Bar clamp with a backplate and strap slots for your own elastic or hook-and-loop straps, and a recess for a foam or TPU pad. Sustained vibration can affect some phone cameras. Check fit and clearance on your own bike before riding.
• Disc rotor rack - Workshop rack that stores disc rotors flat and apart in facing slots, with a back stop. For storage on the bench.
• Single-speed spacer test ring - Plastic test ring for trying chainline before machining real spacers. A fit-checking piece only, not for riding.
• Stick-on cable guide - Stick-on guide with a snap-in channel for housing or hose where there is no boss and a tie will not sit. Check fit and clearance on your own bike before riding.
• Truing stand pointer - Replacement pointer arm for a wheel-truing stand, with a slot for the stand's own bolt. Match the bolt size to your stand.

Cable management

• Screw-on cable clip - Holds one round cable against a wall or desk.
• Six-way cable comb - Keeps six cables in a tidy row. Cables snap in from the front.
• Adhesive cable clip - Snap-in channel for cables up to 6 mm.
• Cable winder - Flat H winder for earphones and chargers, with a slot for each end.
• Desk cable grommet - Flanged ring for a drilled desk hole, with a flexible slotted cover for cables.
• Cable label tag - Clip-on tag with a flat writing face.
• Under-desk cable channel - Open-top J channel in 200 mm sections.
• Cable dock - Low rounded desk block with three slots that keep cable ends from falling behind the desk.
• Cord shortener - Spool with a slotted cover that the spare cable winds into.
• LED strip clip - C-shaped clip for low-voltage LED strip on a shelf edge or cabinet underside.
• Monitor post cable clip - Snaps onto a round monitor stand post and holds three cables.
• Power brick holder - Open cradle for a laptop power brick, cable exits both ends.
• Power strip mount - Lipped cradle with an end stop for a flat power strip.
• Mouse cable clip - C-shaped clamp for a desk edge that keeps a mouse or headset cable from sliding off.
• Under-desk cable tray - Open-topped mesh basket for a power strip, 240 mm long.

Desk and storage

• Gridfinity baseplate - Open-frame grid for drawers and desks. Holds Gridfinity bins.
• Gridfinity bin - Drops into any Gridfinity baseplate. Stacking lip, no magnets.
• Battery holder - Cells stand upright in a grid of pockets.
• Bookend - L bookend whose base plate sits under the books, rubber-foot recesses.
• Business card holder - Cards lean back at 15°, thumb cut-out at the front.
• Book page holder - U-clip that keeps a paperback open.
• Desk tray - Keys, phone and loose bits. Rounded rim, scoop at the front.
• Adjustable drawer divider - Two halves that clip together. A flexing end pad wedges between the drawer sides.
• Drawer tray - Sits loose in a drawer. Finger scoop at one end to lift it out.
• Breadboard base plate - Flat base plate with a low lip for a half-size solderless breadboard. Non-electrical.
• Pen cup - Three rounded tubes at different heights on one base.
• SD card holder - SD and microSD cards upright in angled slots, thumb notch to lift each out.
• Gridfinity bit holder - Holds 1/4 inch hex bits upright. 12 bits per grid unit.
• Gridfinity screwdriver holder - Holds screwdrivers upright in holes from 8 to 14 mm.
• Slide-in label holder - For shelves and bins. A paper or card label slides in from the side.
• Letter rack - Desk rack for letters and mail, three slanted slots.
• ID card holder - Slide-in sleeve for a bank-card-size ID card, with a window and a lanyard slot.
• Magazine file - Open-top desk file for A4 magazines or folders, with a sloped front and a finger scoop.
• Electronics project box - Two-piece box: base and lid are separate parts.
• Monitor memo clip - Clip that grips the top bezel of a flat monitor and holds a paper note or card in a slot.
• Remote control caddy - Holds remotes upright beside the sofa.
• Shelf divider - Clip-on upright, 150 mm tall.
• Pen loop - Stick-on loop for a notebook cover that holds a pen.
• Wall pen rack - Wall rack with a row of slots for pens or markers.
• Gridfinity lid - Flat lid for a Gridfinity bin, held by its lip, with a finger notch and a label slot.
• Gridfinity spacer strip - Filler strip for the leftover gap between a Gridfinity baseplate and a drawer wall.
• USB stick holder - Holds USB-A flash drives upright by their connectors.
• Small wall shelf - One-piece wall shelf with brackets moulded in.
• Open-front storage bin - Open-front bin for a shelf, cupboard or desk, with a sloped front, a finger scoop and a small label slot.
• Sticky note holder - Desk block with a shallow tray and a finger scoop for a square pad of sticky notes.
• Hexagonal pen cup - Single hexagonal pencil cup with no compartments.
• Stacking paper tray - Open paper tray with corner posts that locate into the tray above, and a finger scoop in the front edge.
• Whiteboard marker tray - Marker tray for under a whiteboard or on any wall, with a back plate and an open front trough that slopes slightly so pens roll to one end.

Fixings and hardware

• Round spacer - Stand-offs for electronics, shelving and repairs.
• Cable tie mount - Screw-on base a cable tie threads under, two directions.
• Corner brace - Internal 90° brace for timber frames and boxes.
• Bolt end cap - Domed cover for a protruding bolt end or hex nut.
• DIN rail mount - Clips on 35 mm DIN rail. Plate with M3 holes for a board.
• Door wedge - 10° ramp, grip ribs underneath, finger hole.
• Flat washer - Plain metric washers, ISO 7089 outside sizes.
• Furniture foot - Screw-on round foot with a felt-pad recess.
• Hole plug - Covers a drilled hole in furniture. Barbed stem.
• Closet rod socket - Sold singly: closed cup or open U for dropping the rod in.
• Curtain rod bracket - Open cradle with a retaining lip.
• Rope cleat - Horn cleat for blind cords and light ropes.
• Shelf bracket - L bracket with a curved web.
• Hose adapter - Steps between two hose or port sizes, lead-ins at both ends.
• Hand wheel - Spoked wheel with a spinner handle.
• Finishing washer - Cup washer with a conical seat for a countersunk screw. Cosmetic.
• Extrusion end cap - End cap for aluminium extrusion. Four tabs push into the slot openings, with a notch to lever it out.
• Screw head cover - Snap-in dome that hides a screw head in a counterbore.
• T-shaped mending plate - Flat T plate, 3 mm thick, for joining timber or board edges.
• Key colour cap - Colour-code cover that pushes over a house key head to tell keys apart, with a hole for your own ring. The shank is left open.
• Wing knob - Two-lobed hand knob that presses onto a hex bolt head.
• Square tube cap - Push-on end cap for square or rectangular tube.
• Circuit board standoff - Hex spacer post for lifting a circuit board off a panel, with an M3 nut trap at one end. No electrical function.
• Panel grommet - Flanged edge grommet for a drilled hole in a sheet or panel, with a side slot so a cable drops in sideways.
• Penny washer - Wide plain washer with metric hole sizes, for spreading a screw head over wood or board. Printed in a batch of ten.
• Valve cap - Hex-ridged dust cap for a bicycle or vehicle tyre valve. Keeps dirt out.
• Slat end cap - Shell that pushes over the end of a wooden bed or shelf slat, with a thumb notch to lever it off. Cosmetic.
• Split spacer - C-shaped spacer that clips sideways onto a rod or screw shank without taking it apart.
• Square tube plug - Inside plug with a flange for square steel or aluminium tube.

Furniture parts

• Shelf-pin support - Replacement shelf support for bookcases and cabinets.
• Tube leg cap - Protects floors under round metal chair and table legs.
• Chair glide - Protects floors under square-tube legs.
• Curtain rod finial - Rounded ball end for a curtain rod.
• Corner cap - Rounded cap that covers the corner of a board edge. Cosmetic.
• Curtain clip - C-shaped clip with a closed ring above for hanging a curtain panel from a rod.
• Door bumper - Wall-mounted dome that stops a door.
• Dowel end cap - End cap for wooden dowels and broom handles.
• Drawer stop - Block that stops a drawer short of the back of the cabinet.
• Magnetic door catch - Two-piece cupboard door catch: a housing with a pocket for a disc magnet and a strike with a pocket for a steel disc. Magnet and steel disc not included.
• Door finger plate - Flat plate for around a door handle, with four screw holes. Cosmetic.
• Frame turn button - Oval turn button that holds the back of a picture frame or a small panel, turning on its own screw.
• Levelling shim (pack of four) - Wedge shim with a ribbed top face for levelling a table or cabinet foot. Not for machinery.

Garden

• Bean pole connector - Joins three garden canes at the top of a wigwam. Hole through the top for twine.
• Drip line stake - Holds irrigation tube off the ground. Snap clip on a 120 mm spike.
• Cane cap - Rounded cap that covers the top of a garden cane.
• Plant label - Spike with a flat face for writing.
• Plant support clip - Holds a stem loosely to a cane.
• Seedling tray - Tapered square cells with drain holes.
• Twine dispenser - Hanging cup and lid for a ball of garden twine.
• Garden hose guide - A spike with a roller-shaped head that keeps a hose off the plants.
• Hose hanger - Wide curved saddle for a coiled garden hose.
• Line winder - H-shaped spool for winding twine or builder's line. A slot at the flange edge holds the line.
• Plant pot saucer - Saucer with feet ribs underneath.
• Pot feet - Set of three wedge feet that lift a planter.
• Seed dibber - Hand tool for sowing, with depth marks every 10 mm.
• Ground peg - U-shaped peg for pinning weed fabric, fleece or netting to soil. Soft soil only.
• Post cap - Flat-top cap with a drip lip for a square fence post.
• Hoop clip - C-clip for holding fleece, mesh or polythene to a garden hoop or cane, with a pull tab to open it.
• Plant pot - Round tapered pot with a rounded rim, three drainage holes and a low foot ring. For ornamental plants.

Handles and knobs

• Cabinet bar pull - Kitchen and wardrobe doors. 24 mm finger gap.
• Round cabinet knob - Drawers and cupboard doors.
• D-shaped bar pull - Arched pull for drawers and doors.
• Flat bar pull - Slim modern pull for drawers and doors.
• D-shaft knob - For 6 mm D-shafts on pots, encoders and appliances. Pointer line, knurled grip.
• Hexagonal cabinet knob - Drawers and cupboard doors.
• Square cabinet knob - Drawers and cupboard doors. Square with rounded corners.
• Cup pull - Drawer cup pull.
• Edge pull - Slips over the top edge of a drawer front.
• Star knob - Five-lobe clamping knob with a captured hex nut.
• T-handle knob - Bar handle over a hex bolt head.
• Drawer knob backplate - Plate behind a cabinet knob that hides screw marks. Decorative chamfered edge.
• Thumb knob - Knurled knob that presses onto a hex-head bolt.
• Mushroom cabinet knob - Mushroom-shaped knob with a domed head, for drawers and cupboard doors. Cosmetic.
• Sliding door pull - Flush round finger cup for sliding doors.
• Pull cord handle - Plain tapered grip for the end of a light or blind cord, with a recess for the knot. A grip only, not a safety device.
• Tab pull - Flat tab with a finger hole, glued to a drawer or cupboard front.

Hobby

• Bike bottle cage - For a 74 mm bottle on the standard 64 mm M5 bosses.
• Bracelet stand - Tabletop stand for hanging one bracelet.
• Display stand - Round plinth with a shallow pocket for a model, figure or card.
• Bookmark clip - Flat page clip with a decorative head and a slot for a ribbon.
• Filament clip - Clicks onto a spool rim and holds the loose end.
• Paint bottle rack - Three tiers of six hobby paint bottles.
• Dice rolling tray - Rounded walls and a raised grid floor, one corner scooped for a finger lift.
• Bobbin holder - Bobbins stand upright on short pegs. Sized for class 15 bobbins.
• Fridge magnet body - Disc body with a pocket on the back for a disc magnet. Magnet not included.
• Plain button - Plain sew-through button with two or four holes. Decorative.
• Chalk holder - Pocket tube for a stick of blackboard chalk, with a slit along one side. Hand use only.
• Keyring tag - Blank tag with a 5 mm ring hole and a recessed face for a label.
• Cord toggle - Barrel toggle for a drawstring or cord, with two parallel holes. Decorative, not a safety stop.
• Miniature base - Round tabletop-game base with a recess for glue and a slot for a peg.
• Paint brush drying rack - Holds eight brushes bristle-down at an angle, in 6 and 9 mm holes.
• Knitting needle cap - Domed end cap that stops stitches sliding off a straight needle. Sold as a pair.
• Playing card holder - Keeps a hand of up to 13 cards fanned.
• Earring board - Plate with a grid of small holes for hanging earrings by their hooks, on a wall or inside a drawer lid.
• Paint palette - Flat mixing palette with round wells, a thumb hole and a raised lip.
• Miniature painting handle - Hand-held grip with a clip arm that holds a miniature by its base while you paint.
• Floss bobbin - Card-shaped bobbin for winding embroidery thread, with a notch in each short edge for the thread end.
• Yarn bowl - Open bowl for knitting and crochet with a slot over the rim for the yarn.
• Zip pull - Pull tab with a 3 mm loop slot for a cord.
• Paint stirrer - Flat stirring paddle for paint tins and craft paint, with three slots. Expect it to stain.
• Spool bore adapter (pair) - Pair of ring collars that fit a filament spool onto a smaller axle.
• Spur gear - Plain spur gear for craft and model projects, module 1, with a bore and a grub-screw hole. Hand-turned use.
• Tile rack - Sloped rack that holds seven tabletop-game tiles upright for reading.

Hooks and hangers

• Wall coat hook - Hallways, bathrooms, sheds.
• Adhesive hook - Small hook on a plate with a recess for an adhesive strip (20×50 mm).
• Desk-edge bag hook - Clips over the edge of a desk, hook below.
• Ceiling hook - Open J hook for plants and lights. Spurs stop it turning.
• Broom holder - Wall clip for a broom or mop handle.
• Under-desk headphone hook - Wide rounded saddle under the desk edge.
• Key rack - Rounded hooks under a small shelf for a phone or wallet. Key rings 22 mm or larger.
• Curtain tieback hook - Ball-ended peg for a curtain tie-back or rope loop.
• S hook - For rails and wire racks. One end closes slightly so it stays on.
• Hanger stop - Slide-on spacer for a wardrobe rod that stops hangers bunching together.
• Curtain ring - Ring with a snap catch and an eyelet loop for a clip, for hanging a curtain panel from a pole.
• Over-door hook - Double hook on the room side of a door.
• Peg rail - Rail of round pegs for a hall or utility room. The 400 mm rail is printed as two sections (left and right) that join together.
• Spray bottle hanger - Hangs a spray bottle by its neck from a rail or rod.
• Tie and belt rack - Wall rack with rounded pegs.
• Under-shelf hook - Slides onto a shelf edge with a hook underneath.
• Wall hook rail - Rail with rounded angled pegs.
• Sock clip - C-clip that keeps a pair of socks or gloves together, with a pull tab. Keep out of hot washes.
• Umbrella hook - J-shaped wall hook for an umbrella handle.

Kitchen and bathroom

• Bag clip - One piece: flexing hinge, toothed jaws, snap catch with a pull lip.
• Carrier bag dispenser - Wall tube for plastic bags with a pull hole at the bottom.
• Clothes peg - One-piece peg with a flexing spring.
• Drinks coaster - Coaster for desks and tables with a raised rim.
• Lid rack - Holds container lids upright, 25 mm slot pitch.
• Paper towel holder arms - Two drop-down arms under a cabinet. The roll sits on a 30-40 mm wooden dowel (not included).
• Razor holder - U slot for a razor plus a ledge for a can up to 66 mm.
• Bin liner clip - C-clip that tucks a bin liner over the rim of a rubbish bin, with a pull tab to open it.
• Shower corner shelf - Quarter-circle shelf with drain slots and a raised rim.
• Shower curtain hook - Snap closure over the rail, pin through the curtain eyelet.
• Soap dish - Raised ribs over a sloped floor that drains to a spout.
• Tiered spice rack - Three steps for jars in a cupboard. Jars up to 45 mm across sit flat.
• Sponge holder - Slotted cradle on keels so water drains away.
• Toilet roll holder - One-piece arm with an upturned end.
• Toothbrush holder - A well for each brush plus a tube slot, drainage holes in the base.
• Hair tie holder - Upright post for storing hair ties, scrunchies or bracelets.
• Wall tumbler ring - Wall ring that holds one tumbler or toothbrush glass. The front is cut away so the glass lifts out forwards.
• Napkin holder - Upright holder with an open centre. 180 mm wide.
• Napkin ring - Plain ring, 30 mm wide.
• Ring dish - Small trinket dish with a centre cone for rings.
• Shoe horn - Curved blade with a hanging hole.
• Toothpaste tube squeezer - Slotted key that rolls up a tube.
• Double towel hook - Two rounded prongs.
• Shower head holder - Wall holder for a handheld shower head, with a funnel mouth.
• Tea towel clip - Wall clip that holds a tea towel by its edge on a flexing tongue. For dry towels.
• Toilet seat bumpers (set of four) - Low domed stick-on bumpers for the underside of a toilet seat or lid, with a recess in the base for a double-sided pad (pad not included).

Pipes and hoses

• Pipe clip - Snap-in saddle clip for pipe and conduit.
• Tube end cap - Push-on cap for round tube. Grips from 0.3 mm under to 0.3 mm over size.
• Hose connector - Barbed joiner. Not for pressurised or drinking water.

Signs and labels

• Arrow sign - Arrow-shaped plate for a path, door or shelf, with optional raised lettering.
• House number - A single raised digit, 0 to 9.
• Label plate - Blank drawer or shelf plate with a recess for a sticker or paper label.
• Place card holder - Small angled slot block for a table place card or recipe card.
• Room sign holder - Wall plate with a slide-in pocket for a paper sign.
• Stencil letters - Fixed alphabet set of flat craft stencils, A to Z and 0 to 9 over three plates (A-I, J-R, S-Z and 0-9). Not custom text. Reusable craft stencil.
• Tactile locating dot - Small stick-on dome for marking a button or appliance control by feel.
• Wire shelf label clip - Label holder that clips onto wire shelving, with a recess for a paper label.

Stands

• Laptop riser - Raises the back of a laptop about 60 mm. Front lip stops it sliding.
• Phone stand - Tapered slot fits phones with or without a case. Cable gap underneath.
• Desk-edge shelf - Small shelf that hooks over the back edge of a desk. Front lip. 100 mm wide.
• Tablet stand - Tall front lip for tablets in cases, charging-cable gap.
• Glasses stand - Holds one folded pair of glasses on a nose-bridge saddle.
• Phone wall shelf - Small shelf for a phone while it charges. Front lip and cable slot.
• Watch stand - Display stand for a wristwatch. The strap wraps over a curved rest.

Workshop

• Angle gauge - Flat plate with notches at 15, 22.5, 30, 45 and 60 degrees, each labelled. A layout aid; accuracy is not claimed.
• Bench dog - Stop for a workbench dog hole, 10 mm above the bench.
• Drill bit stand - Stepped block with engraved sizes.
• Drill guide block - Keeps a bit square to the work. Holes for 3 to 10 mm bits, V groove for round stock.
• Centre finder - V block with a straight edge on the bisector, for finding the centre of round stock.
• Pegboard bin - Open-front parts bin with a label recess.
• Pegboard hook - Standard 1/4 inch holes on a 1 inch grid, with an anti-lift peg so it stays put.
• Pegboard screwdriver rack - Eight screwdriver shafts in a row, hangs on 1/4 inch holes on a 1 inch grid.
• Sanding block - Quarter-sheet sandpaper, pinched in a wedge slot at each end.
• Wall spool holder - Holds filament or wire spools with a 52-55 mm hub. End lip stops them sliding off.
• Extension cord hook - Wide wall hook for a coiled cord or hose.
• Wall tool rack - Screwdrivers in one row, pliers in a row of wider slots.
• Drill depth stop - Collar that slips over a drill bit to set a drilling depth. Flat face rests on the work.
• Workshop funnel - Oil, coolant, screws. Not for food. Vent rib on the spout.
• Handle drilling jig - Drilling template for cabinet handles at 64, 76, 96, 128 and 160 mm centres, 5 mm guide holes.
• Spanner rack - Spanners hang by their heads in angled slots, 8 to 19 mm.
• Hex key holder - Holds nine hex keys upright, 1.5 to 10 mm, each hole labelled.
• File handle - Tapered grip handle for a tang file or rasp.
• Scissors holder - Wall holder for closed scissors or snips.
• Glue spreader - Flat notched spreader for wood glue and filler on the bench. Hand use only.
• Glue-up square - Flat L-shaped square for holding two boards at right angles while glue sets, with a slot in each leg for your own clamps. An alignment aid, not a precision square.
• Small-parts sorting tray - Compartments with scooped floors. Stacking lip.
• Tape measure holder - Wall holder for a tape measure belt clip.
• Tape roll holder - Wall spigot for a roll of tape, with an end rim.
• Setup block set - Flat 20×60 mm bars for setting a gap or height at the bench, each marked with its thickness. Four blocks, one file per thickness. A setup aid; accuracy is not claimed.
• Pegboard pliers rack - Bar with angled slots for hand pliers and snips, for 1/4 inch hole pegboard on a 1 inch grid.
• Pegboard shelf - Small shelf with a ledge and front lip for 1/4 inch hole pegboard on a 1 inch grid, with an anti-lift lip on the pegs.
• Radius gauge - Flat plate with a concave and a convex quarter-circle edge and the radius engraved on it, for checking a rounded edge by eye. A visual guide only.
• Mitre saw guide block - Hand-held block with a straight saw slot at 90 or 45 degrees to its fence face. Hold the fence face against the timber and saw through the slot. The slot floor is 4 mm above the base.
• Screw size gauge - Plate of numbered round holes for sorting loose screws, bolts and drill bits by diameter. The numbers are hole diameters.
• Vice jaw liner (pair) - Pair of L-shaped liners that drop over the top of a bench vice jaw so the work is not marked, with a recess in the face for a self-adhesive felt pad (pad not included).